The process of draining a GE dishwasher typically involves a few simple steps, including activating the drain cycle and checking for any blockages that might be causing the water to not drain properly. By following the correct steps, you can troubleshoot and resolve drainage problems, making your dishwasher work efficiently again.
By following these steps, you can maintain the optimal performance of your GE dishwasher and ensure it continues to serve you well in keeping your dishes clean and shiny.
How to Drain the Water in Your GE Dishwasher

Step 1: Identify the Clog

Before you dive into any draining procedures, it’s essential to identify if there’s a clog in your dishwasher.
- Press the start button once and observe if the water starts draining. If not, move on to the next step.
Step 2: Activating the Drain Cycle
To start the dishwasher’s drain cycle:
- Press the start button again and hold it for 2 to 3 seconds.
- The dishwasher’s drain cycle will kick in, and you’ll notice the water starting to drain.
Step 3: Check for Blockages
Clearing out the blockages will help the water flow freely and ensure a thorough draining process.
- If the water is not draining completely, check for any blockages in the dishwasher.
- Clear out any debris or objects obstructing the drainage.
Step 4: Repeat if Necessary
- Sometimes, stubborn clogs require multiple attempts to clear completely.
- Repeat the start button and holding process until all the water drains out.
How to Clean Your GE Dishwasher Filter

Step 1: Identify the Issue
To begin draining your GE dishwasher, you’ll first need to identify if there is a drainage problem.
- If you notice pooled water at the bottom of your dishwasher, there might be a clog in the filter.
- Close the dishwasher door and proceed to the next step.
Step 2: Initiating the Drain
Once you’ve confirmed the drainage issue, it’s time to activate the dishwasher’s drain cycle.
- Hold down the start button for three seconds to activate the dishwasher’s drain cycle.
- Listen for the draining sound from the dishwasher.
Step 3: Wait and Observe
This step may vary depending on your dishwasher model, so make sure to follow your user manual for specific instructions.
- Give it a minute to ensure all the water has drained out.
- You may hear the dishwasher continuing to drain over the sink.
Step 4: Check for Water Residue
- Once the draining stops, open the dishwasher door to check if there is any remaining water at the bottom.
- If the water is gone, your dishwasher is now successfully drained.
Troubleshooting a GE Dishwasher That Won’t Drain

Step 1: Check for Blockages
Blockages in the dishwasher’s drainage system are a common culprit for water not draining properly.
- Remove the lower rack to access the drain pump and check for any debris or obstructions.
- Use a flat-head screwdriver to pull out the tabs on each side to reveal the pump.
Step 2: Inspect the Drain Pump
If the dishwasher continues to have draining issues after checking for blockages, the next step is to examine the drain pump.
- If you suspect a faulty drain pump, remove the pressure switch to access it easily.
- Twist the pump to the left and pull it out to inspect for debris or signs of damage.
Step 3: Replace the Drain Pump (if needed)
If the drain pump is found to be damaged or burnt out, it may need to be replaced. A malfunctioning drain pump can significantly hinder the dishwasher’s drainage process.
- If the pump is burned or damaged beyond repair, consider replacing it with a new one.
- Refer to the dishwasher’s model number to find the compatible replacement.
How to Get GE Profile Dishwasher to Drain

To get your GE Profile dishwasher to drain:
- Check for blockages in the drain filter and pump.
- Run the dishwasher’s drain cycle.
- Ensure the drain hose is properly connected.
- If issues persist, consider professional repair or contact GE support.
Conclusion
Now you’re equipped with the knowledge to handle any draining issues with your GE dishwasher like a pro! Follow the step-by-step guide to drain the water effectively and troubleshoot any drainage problems that may arise. Remember to clean the filter regularly to keep your dishwasher running smoothly.
Frequently Asked Questions
My GE dishwasher is not draining. What could be the problem?
There could be various reasons, including a clogged filter, debris in the drain pump, or a faulty pump.
How often should I clean the dishwasher filter?
It’s a good practice to clean the filter once a month or every 2-3 months to maintain optimal performance.
Can I use any replacement drain pump for my GE dishwasher?
No, it’s essential to use a compatible replacement drain pump that matches your dishwasher’s model number.
Key Points Summary
- Press start button once, then again and hold for 2-3 seconds to drain water.
- Clear blockages if necessary, repeat draining process if needed.
- Hold start button for 3 seconds to activate dishwasher drain cycle.
- Wait for draining sound, check for remaining water, and voila!
- Troubleshoot clogs or faulty drain pumps for non-draining issues.
- Clean the filter regularly for optimal dishwasher performance.