When a “Samsung Dryer is Not Heating,” it refers to a common issue where a Samsung brand clothes dryer fails to produce the necessary heat during its drying cycle. This problem can result in clothes remaining damp and not getting properly dried, which can be frustrating for users. The lack of heat in the dryer can be caused by various factors, but one of the most common reasons is a malfunctioning heating element.

Unplug and Gather Tools

  1. Safety First: Prioritize safety by unplugging your dryer to avoid any electrical hazards.
  2. Tools Needed: You’ll require a Phillips head screwdriver, a voltmeter/ohmmeter, and a bit of patience.

Access the Dryer’s Interior

How to Fix Samsung Dryer Not Heating | Common Problem
Common Samsung Dryer Problems
  1. Top Panel Removal: Open the dryer door and locate the screws holding the top panel in place. Unscrew and lift the top panel, then prop it securely against a wall or other stable support.
  2. Front Panel Disconnection: Inside, you’ll find screws securing the front panel, including some behind the door. Remove these screws carefully and detach the front panel. Pay close attention to the wires connected to the door switch.
  3. Disconnect Wiring: Unplug the wiring connections as needed. It’s wise to take photos for reference before disconnecting any wires.
  4. Access the Heating Element: The heating element sits beneath the drum, so you’ll need to remove the drum to access it. To do this, remove the screws securing the bulkhead and disconnect any additional wiring.

Examine the Heating Element

Samsung Dryer Heating Element
How to Replace Heating Element in Samsung Dryer
  1. Belt Removal: Locate the drive belt that encircles the drum and detach it from the motor and idler pulley.
  2. Remove the Drum: Carefully lift out the drum. While it’s out, seize the opportunity to vacuum any accumulated dust and lint from within the dryer.
  3. Heating Element Check: Employ your voltmeter/ohmmeter to check the continuity of the heating element. If there’s no continuity (the needle doesn’t move), it’s a strong indicator of a damaged element.

Replace the Heating Element

  1. Prepare the New Element: If your heating element is indeed the culprit, replace it with a new one. Carefully detach the wires from the old element.
  2. Disassemble the Element Housing: Unscrew the element housing, exposing the broken element wire.
  3. Install the New Element: Insert the new element into the housing, secure it, and reattach the wires.

Reassemble Your Dryer

  1. Reinstall the Drum: Carefully slide the drum back in, ensuring it rests properly on the idler wheels.
  2. Bulkhead and Wiring: Reattach the bulkhead and reconnect all wiring connections.
  3. Drive Belt: Reattach the drive belt around the drum, motor, and idler pulley.
  4. Front Panel: Reinstall the front panel, securing it with screws. Reconnect any wiring and plug in the door switch.
  5. Top Panel: Close the dryer’s top panel and secure it with screws.

Test Your Dryer

  1. Plug It In: Finally, plug in your dryer and test it to ensure it’s heating up properly. You should feel the warmth of success!

Step-by-Step Instructions

Samsung DVE50M7450W/A3 dryer failing to produce heat, leaving your clothes damp and frustrating your laundry routine. Follow these steps to get your dryer heating again.

Step 1: Safety First – Unplug the Dryer

Before you start any repair work, always ensure your safety. Begin by unplugging the dryer from the power source. Safety should always be a top priority.

Step 2: Access the Dryer’s Top

  1. Locate and release the tabs on the top of the dryer.
  2. Gently lift the top and prop it against a wall or sturdy surface to keep it out of your way.

Step 3: Remove the Front Panel

How to Fix Kenmore Front Load Washer that won't Drain
Front Panel
  1. Open the dryer door and locate the tabs on the inside.
  2. Release the tabs, which may vary depending on your dryer model. They may lift up or require a slight push to release.
  3. Carefully remove the front panel and set it aside.

Step 4: Access the Heating Element

Now that you have access to the dryer’s interior, it’s time to get to the root of the problem – the heating element.

Step 5: Disconnect the Heating Element

  1. Take note of the wiring configuration to ensure proper reassembly later.
  2. Carefully disconnect the wires from the heating element. A photo for reference can be helpful.
  3. Remove any screws holding the element in place and remove it from its housing.

Step 6: Test the Heating Element for Continuity

  1. Using an ohm meter, set it to measure continuity (ohms).
  2. Test the heating element by touching the meter’s probes to its terminals.
  3. If there is no continuity, it’s likely that the heating element is faulty and needs replacement.

Step 7: Replace the Faulty Heating Element

  1. Once confirmed that the heating element is indeed faulty, obtain a replacement.
  2. Carefully install the new heating element, securing it in place with screws.
  3. Reconnect the wires to their proper terminals based on your earlier reference.

Step 8: Reassemble the Dryer

  1. Begin by positioning the front panel back in place.
  2. Secure the front panel with the screws you removed earlier.
  3. Reattach the wiring to the top of the dryer.
  4. Close the dryer door and ensure that the tabs on the front panel lock into place.
  5. Lower the top of the dryer back down, making sure it rests securely.

Step 9: Test Your Dryer

  1. Plug the dryer back into the power source.
  2. Turn on your dryer and check if it’s now producing heat.
  3. You should feel relieved as your clothes start to warm up!

Samsung Dryer Spinning but not Heating

How to troubleshoot a Samsung dryer that is spinning but not heating. Here’s a summary of the steps:

  1. Check Proper Voltage: Ensure that the dryer has the proper voltage supply. This should be around 240 volts. If there’s an issue with voltage, it can affect the heating element.
  2. Test Heater Relay: To check the heater relay, disconnect the dryer, remove the control board, and carefully test the relay for proper voltage. It should provide 120 volts to the heating element.
  3. Check Thermistor: While a faulty thermistor might not directly cause the dryer to spin but not heat, it’s good to check it for error codes. If you receive specific error codes (e.g., TS or ATO), test the thermistor’s resistance using an ohmmeter. At around 77 degrees Fahrenheit, it should read around 10,000 ohms.
  4. Inspect Heating Element and Thermostats: To access the heating element and thermostats, you’ll need to disassemble the dryer. Once accessed, use an ohmmeter to test the heating element, high-limit thermostat, and thermal cutoff. They should all show resistance when tested.
    • The heating element should show a resistance reading.
    • The high-limit thermostat should show minimal resistance.
    • The thermal cutoff should also show minimal resistance.

Samsung Front Load Dryer not Heating

  1. Remove the Top and Control Panel:
    • Remove two Phillips head screws on the top panel.
    • Push back and remove the top panel.
    • Pull the control panel from the top to remove it. Unplug the dryer first.
  2. Remove Screws and Front Panel:
  3. Remove Metal Bracket and Wire Ties:
    • Remove five screws on the metal bracket.
    • Remove wire ties.
    • Remove the ducting with three screws.
  4. Clean the Inside:
  5. Access the Heating Element:
    • Remove four screws and lift up to access the heating element.
  6. Test for Continuity:
  7. Replace the Faulty Part:
  8. Reassemble the Dryer:
    • Reattach all wires and components in the reverse order.
    • Ensure the door switch and moisture sensor harness are properly connected.
  9. Perform a Test:
  10. Check for Proper Function:
    • Ensure that the heating element cycles on and off as described.
    • Verify that the dryer operates correctly without any issues.
  11. Final Tips:
    • Don’t forget to plug in the door switch and the moisture sensor harness.
    • If the heating element stays on continuously, further troubleshooting may be needed.

Frequently Asked Question

Why did my heating element break?

Heating elements can break due to various reasons, but one common cause is overheating, often caused by a clogged vent. Regularly cleaning your dryer’s vent can prevent this issue.

Can I fix the heating element myself?

Yes, you can! By following our step-by-step guide and taking necessary safety precautions, you can replace the heating element yourself.

Where can I find a replacement heating element?

Replacement heating elements are available from appliance parts stores, online retailers, or directly from the manufacturer.

In Summary

Fixing a Samsung dryer that’s not heating up is a manageable task with the right guidance. By following these steps and safety precautions, you can have your dryer back in action in no time.

Key Takeaways and Important Points:

  • Safety first: Always unplug the dryer before attempting any repairs.
  • Access the heating element by removing the top and front panel.
  • Test the heating element for continuity to confirm if it’s faulty.
  • Replace the heating element if there is no continuity.
  • Reassemble the dryer in the reverse order of disassembly.
  • Regularly clean your dryer’s vent to prevent overheating and future issues.

Similar Posts